Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateWhy Hempstead Homeowners Choose Ghost Controls Gate Repair
Ghost Controls in Hempstead means working on the actuator, control board, and drive hardware that actually moves your gate, not just the hinges and latch. We’re an independent Ghost Controls service provider serving Hempstead and the surrounding village streets, and we carry the board-level and gear-level parts that let us fix what other companies replace. Call (516) 559-4870 for a written quote before any work begins.
Ghost Controls builds swing and slide gate repair openers popular with Hempstead homeowners because the systems retrofit cleanly onto older gates. The village has a lot of 1920s through 1950s homes with decorative wrought iron gates that were never designed for automation. Ghost Controls kits adapt to those gates better than most, which is why we see so many of them on residential streets near the village center. That same pre-war ironwork, however, puts real strain on the operator. When the gate is heavy, slightly warped, or corroded from Atlantic humidity, the Ghost Controls actuator absorbs that stress. Knowing how the brand responds to that stress is the difference between a fix that holds and one that fails again in six months.
We are not authorized by Ghost Controls, and we don’t claim to be. What we offer is field experience with Ghost Controls TSS1, AXDP, DTP1, and SLD openers, plus the diagnostic discipline to find the actual fault before quoting a repair.
Why Trust Carver Gate Repair Hempstead for Your Ghost Controls Gate Repair?
Lonnie Burke owns Carver Gate Repair Hempstead and grew up around the trade in Los Angeles before training at Los Angeles Trade-Technical College. He spent the better part of two decades working gates and operators across the New York area. His crew has served Hempstead for years, running service calls near Hofstra University’s surrounding blocks as often as anywhere else in the village. Lonnie is known for diagnosing operator failures and misaligned tracks quickly, no guesswork and no parts ordered on a hunch. When he’s not on a job, he’s usually recalibrating a limit switch at the workbench in his garage.
That background matters when the call is for Ghost Controls equipment. Ghost Controls boards, actuators, and remotes have specific failure patterns. A technician who works on several brands each week can misread those patterns. Our technicians work on Ghost Controls systems every week across Hempstead, from stripped rack drives on older sliding gates to failed control boards on late-model swing actuators. We know the brand’s quirks without relying on manufacturer authorization.
Every Ghost Controls repair from Carver Gate Repair Hempstead carries The Garrison Standard: a written price delivered before any work starts, a written guarantee on every repair good for a full year, and a free second visit if the repair fails inside that guarantee window. Phones are answered by a live person 24 hours a day. That’s not an upsell. It’s how we’ve operated since 2008.
Key takeaways:
- Independent Ghost Controls service, not manufacturer-authorized
- Written price before work starts, guaranteed in writing for one year
- Background-checked, uniformed technicians on every call
- Owned by Lonnie Burke, with two decades of gate and operator experience in the New York area
- Live-person phone coverage 24/7, including weekends and holidays
Styles & brands we work with
Common Ghost Controls Gate Repair Problems We Fix in Hempstead
These are the Ghost Controls issues we see most often on Hempstead gates. Each one has a specific cause and a specific fix, and most are repairable at the part level rather than requiring a whole new opener.
- Stripped plastic gears in the TSS1 Solar Gate Opener actuator. The TSS1 uses a plastic gear set inside the actuator housing. When a gate is heavy, rusted, or slightly warped, the motor stalls against the resistance and the gear teeth strip. Hempstead’s older wrought iron gates are exactly the kind that cause this. We replace the gear set and then address the gate itself, because a new gear set on a binding gate won’t last a season.
- Control board damage from incorrect battery backup connections. Ghost Controls battery backup kits are straightforward, but wiring the battery leads to the wrong terminals sends a voltage spike through the board. We see this on AXDP and DTP1 installations where a previous handyman wired the backup in without checking polarity. The board fails and the gate stops responding. We replace the board and wire the backup correctly, with the system tested through a simulated power outage before we leave.
- Limit switch drift on AXDP models, causing mid-travel stops or gate slamming. The AXDP Automatic Gate Opener relies on limit switches to tell the operator where the gate is in its travel. Over time, vibration, temperature swings, and gate sag move those limits out of position. The gate stops partway open or slams hard against the closed position. We reset the limits and check the mounting bracket for movement that would let the problem return.
- Rust jacking between the steel rack and gate frame on SLD slide openers. The SLD Slide Gate Opener drives a steel rack mounted along the gate’s length. Near Hempstead, moisture from the South Shore salt air and winter freeze-thaw cycles gets between the rack and the frame, rust builds, and the rack lifts away just enough to throw the drive pinion out of alignment. The gate starts grinding mid-travel. We remove the rack, clean the mounting surface, re-secure it on rust-inhibited hardware, and realign the pinion to the rack.
- Burned motor capacitors on DTP1 dual swing actuators. The DTP1 Dual Swing Gate Opener runs each leaf on its own actuator. When a leaf is out of balance or the close-force limit is set too high, the actuator overworks and the capacitor fails. The motor won’t start. We replace the capacitor with a factory-rated unit and then set the force limits correctly so the motor isn’t fighting the gate.
If your Ghost Controls gate is showing any of these symptoms, call (516) 559-4870. We’ll help you identify what’s actually wrong before we schedule a visit.
Ghost Controls Parts & Our Repair-vs-Replace Approach
We always attempt an OEM Ghost Controls replacement board or gear kit first. The aftermarket equivalents often have different torque curves that shorten motor life, and the savings disappear when you’re paying for another repair a year later. For boards, capacitors, gear kits, and limit switches, we stock or can source OEM Ghost Controls parts quickly across Hempstead and the surrounding area.
The honest line on repair versus replace: when a Ghost Controls unit is over eight years old or the gearbox is already compromised, we tell you. Pouring money into a dying drive is a bad deal. If the board is fried, the gears are worn, and the actuator housing shows corrosion, a new operator is often the cheaper fix over a three-year horizon. We quote both paths when it’s close and let you decide.
We also service the surrounding hardware: automatic Ghost Controls repair in Levittown, slide motor repair, and battery backup installation on existing Ghost Controls systems. For a parts-specific quote on your Ghost Controls opener, call (516) 559-4870. Estimates are free.
Our Ghost Controls Service Process – Step by Step
- 1
Diagnosis. We test the operator, control board, limit switches, remote receivers, and the gate’s physical movement before touching a repair. Ghost Controls error beep patterns tell us a lot. A TSS1 beeping three times without moving the gate points to a stalled motor or stripped gear. We confirm with a multimeter and a hands-on check of the actuator before quoting.
- 2
Written quote. You get a price in writing before any work starts, covering parts and labor. The number doesn’t move at the door. If a part is harder to source than expected, we tell you before ordering anything.
- 3
Repair or installation. We replace the failed component with OEM Ghost Controls parts where available, wire battery backups correctly, set force and travel limits, and service the gate itself so the new parts aren’t fighting old hardware.
- 4
Testing. We cycle the gate open and close a minimum of ten times, test remote and keypad function, verify battery backup operation if installed, and check that auto-close and obstruction detection behave correctly.
- 5
Guarantee. Every Ghost Controls repair carries our 365-Day Done Right Promise in writing. If the repair fails within one year, we return and make it right at no charge. If the gate’s not right, we’re not done.
See the difference
Before
After
Before
After
Before
AfterGhost Controls Products We Service & Install in Hempstead
We service and install the Ghost Controls product lines most common on Hempstead gates:
- Ghost Controls TSS1 Solar Gate Opener – single swing, solar-capable, common on residential walk and driveway gates
- Ghost Controls AXDP Automatic Gate Opener – battery-powered swing operator with wireless controls
- Ghost Controls DTP1 Dual Swing Gate Opener – full dual-leaf systems for wider driveway openings
- Ghost Controls SLD Slide Gate Opener – rack-and-pinion slide operators for rolling and cantilever gates
We stock common replacement parts for these units locally: control boards, capacitors, limit switches, gear kits, remotes, and battery backup components. Less common parts we order directly from Ghost Controls supplier channels, usually arriving within days.
We Also Service These Brands
Ghost Controls is a brand we know well, but it’s one of nine gate-motor brands our technicians work on. If you have a LiftMaster on the driveway and a Ghost Controls on the side gate, one call covers both. We also service Mighty Mule and DoorKing systems across Hempstead and Ghost Controls repair in Jamaica, so the right parts and know-how are matched to whatever system is already installed.
FAQs – Ghost Controls Gate Repair Service in Hempstead
No. We are an independent Ghost Controls service provider and are not affiliated with or authorized by the manufacturer. We carry and source OEM Ghost Controls parts, but our authority comes from field experience, not a manufacturer agreement. Being independent also means we’re free to tell you honestly when an older Ghost Controls unit isn’t worth repairing.
We use OEM Ghost Controls parts as our first choice on every repair, including control boards, gear kits, capacitors, and limit switches. We’ve found the aftermarket alternatives often have different torque curves that shorten motor life. When an OEM part is discontinued or backordered, we’ll discuss the aftermarket option with you before installing it.
Most Ghost Controls board, capacitor, and limit switch repairs are finished in a single visit lasting one to three hours. Gear replacement or rack realignment on an SLD slide opener can take a little longer if we’re also treating rust on the gate frame. We’ll give you a time estimate on the written quote before we start. Call (516) 559-4870 if you need same-week scheduling.
We service and install the TSS1 Solar Gate Opener, AXDP Automatic Gate Opener, DTP1 Dual Swing Gate Opener, and SLD Slide Gate Opener, along with their remote controls, keypads, and battery backup kits. If you have an older Ghost Controls unit we haven’t listed, call and we’ll identify it by model number before scheduling.
If your Ghost Controls opener is still under manufacturer warranty, independent service does not automatically void it, provided the work is done competently and without unauthorized modification. We install parts to Ghost Controls factory specifications and we’re careful about wiring, which is where most warranty-damaging mistakes happen. If a repair falls under the manufacturer warranty, we’ll help you file the claim with Ghost Controls.
Ghost Controls gate repair in Hempstead typically runs from $225 for a limit switch or remote receiver fix up to $1,400 or more for a full dual-leaf actuator replacement on a DTP1 system. Control board replacement usually lands between $350 and $600. Gear kit replacement on a TSS1 typically runs $250 to $450. Every job gets a written quote before work starts. For an exact price on your system, call (516) 559-4870 and we’ll walk through what you’re seeing.
Field note: On a residential double swing gate off Peninsula Boulevard, our tech found the Ghost Controls DTP1 operator for the north leaf had a burned motor capacitor and a bent extension arm. We replaced the capacitor with a factory-rated 35µF unit, straightened the arm on a bench press, and reset the close-force limit so the leaf stopped slamming against the stop post. The gate has run clean every cycle since.
A three-beep code on the TSS1 usually means the actuator motor is stalling or the gear set is stripped. On Hempstead gates, the cause is often a rusted or sagging gate that the motor can’t move under normal force. If this is happening, stop trying to run the gate and call (516) 559-4870. Continuing to cycle the opener against a bound gate will finish off the gears if they aren’t already gone.
We can replace just the control board on the AXDP. It’s a board-level swap, and we do it frequently when a voltage spike or a bad battery backup connection has fried the original. The actuator and gear set often don’t need to be touched. We’ll test the board first to confirm the failure before quoting the replacement. Call (516) 559-4870 for a board diagnostic.
We install Ghost Controls battery backup kits on existing TSS1, AXDP, DTP1, and SLD openers. The key to a reliable installation is correct polarity and a clean mounting location away from standing water. We wire the backup, test it through a simulated power outage, and verify the system auto-switches and recharges correctly before we call the job done.
Near Hempstead, where salt air and freeze-thaw cycles work on metal year-round, we recommend cleaning and greasing the SLD rack twice a year. Fall and spring are the two times that make sense before winter ice and after spring thaw. The more important job is checking for rust between the rack and the gate frame, which is the failure we see most often on coastal Long Island slide gates. A rack that’s lifting away from the frame will shred the pinion gear and ruin an expensive operator.
In most cases, no. After a power outage, the Ghost Controls receiver often loses its learned remote codes or resets to factory settings. Before we replace the receiver, we attempt to re-learn the remotes into the board. If the receiver won’t hold codes after reprogramming, then we’ll replace it. Call (516) 559-4870 and we’ll walk you through the first re-learn steps over the phone before scheduling a visit.
Book Your Ghost Controls Service in Hempstead, NY
If your Ghost Controls opener is beeping a fault code, moving the gate halfway, or not moving at all, call (516) 559-4870 for a free estimate. A live person answers 24 hours a day. We’ll talk through what the system is doing, give you a straight answer on likely causes, and schedule a visit where you get a written price before any work begins.
Written by Lonnie Burke, Owner at Carver Gate Repair Hempstead, serving Hempstead, NY since 2008.