Ghost Controls Access Control Installation Nationwide

Ghost Controls Access Control Installation: The Hempstead Owner’s Guide

We stock and install Ghost Controls access control parts across Hempstead, and a typical keypad-to-board replacement or new receiver install runs $260 – $480 installed, parts included. Most jobs are completed the same day we arrive, because our trucks carry the common Ghost Controls boards, keypads, and receivers rather than making you wait on a parts order. The way most owners find us: the gate stopped responding to the remote, the keypad went dead, or the obstruction sensor now trips when nothing’s in the way. You already know Ghost Controls gear is good. What you need is someone who can match the part to the exact board revision you have, because Ghost Controls changed connectors and wiring across model years more than most brands.

Call (516) 559-4870

Which Ghost Controls Models This Applies To

Ghost Controls sells two operator families that dominate the Hempstead market: the AXDP series (single and dual swing gate kits) and the TSS1/TDS1 series (their heavier torque swing operators). The access control side covers the AXPB keypad, the reciever module, and the main control board mounted inside the operator housing. Before we quote a replacement, we read the board revision sticker, usually a white label with a “Rev” letter near the terminal block. Ghost Controls changed the keypad connector from a 4-pin flat plug to a 5-pin round plug around the 2019 production run, and plugging the older keypad into the newer board just leaves you with a dead pad and a blown fuse. That single compatibility gotcha has stranded more Hempstead homeowners than any actual board failure. On OEM versus aftermarket: for Ghost Controls, we use OEM parts when the repair touches the board or safety inputs. Aftermarket wired keypads work fine when the owner just wants an extra entry point, but we won’t put an off-brand wireless receiver on a Ghost Controls system and call it a day.

Signs Your Ghost Controls Access Control Installation Is Failing

• Keypad lights up but the gate won’t move. The keypad is sending a signal, but the board isn’t acting on it. We see this most often after a storm, when a surge nicks the board’s output relay. The keypad is fine; the board’s relay isn’t.
• Remote range dropped from 50 feet to “standing right next to it.” The receiver antenna may have corroded at its connection, especially in Hempstead’s salt-air winters. We replace the receiver module and re-seat the antenna, and range comes back.
• The gate reverses for no reason, then stops responding to everything. The obstruction sensor circuit is misfiring. Ghost Controls boards treat a sensor fault as a stop command. Until that sensor or its wiring is replaced, the board won’t cooperate.
• The gate opens on its own at random hours. A failing receiver can pick up stray signals from nearby garage remotes or municipal radio traffic. Ghost Controls uses rolling-code technology, but a degraded receiver gets sloppy about filtering. We swap the receiver and re-sync your remotes.
• You hear a click from the operator but nothing moves. The board is calling the motor and the motor’s not answering. That’s either a board output failure or a motor drawing dead. We test it before we quote it, because replacing the board when the motor’s burned out wastes your money.

Replacement Cost & What’s Included

Here’s where your money actually goes on a Ghost Controls access control job in Hempstead:

• Control board replacement: $220 – $380 installed, depending on whether it’s a single or dual operator and which board revision you have. The board itself runs $120 – $210, and the rest is labor and wiring verification.
• Keypad replacement: $180 – $260 installed. The Ghost Controls AXPB keypad is weather-rated, but Hempstead’s freeze-thaw cycles eventually crack the housing gasket. We replace the keypad and the wiring pigtail together.
• Receiver module replacement: $190 – $280 installed, including re-programming your existing remotes and clearing stale codes from the board.
• Full access control refresh (board, keypad, receiver, remotes synced): $450 – $650 installed. We reserve this for systems older than 8 years where multiple pieces are failing at once.

Before any part gets ordered or a wire gets pulled, you get a written price. That number includes the part, the labor, and the programming. It does not change once the job opens, unless we uncover something structural that we show you and you approve before we proceed. Every access control repair we do carries our written guarantee for a full year. If that part fails inside 365 days, we come back and make it right, no charge for the second visit.

DIY or Call Us?

There’s an honest line here, and it matters. You can safely check the operator’s power source, confirm the breaker hasn’t tripped, and verify the keypad wiring looks intact at the connector. Those are visual checks and they cost you nothing. What you shouldn’t do is open the control board housing and start probing terminals. Ghost Controls boards run live low-voltage control circuits, but they sit next to the motor leads carrying household current, and the boards themselves are static-sensitive. We’ve had Hempstead homeowners run a multimeter across the wrong two terminals and turn a $200 board replacement into a $400 board-and-keypad replacement. If you’ve done the visual checks and the gate still won’t respond to the keypad or remote, call (516) 559-4870 and we’ll diagnose it on site. The diagnostic is part of the free estimate. If the gate’s not right, we’re not done.

FAQs