FAAC Hinge & Roller Replacement Nationwide

FAAC Hinge & Roller Replacement: The Hempstead Owner’s Guide

FAAC hinge and roller replacement in Hempstead typically runs $220 to $480 installed, depending on the model and how many roller assemblies need to be swapped. We stock FAAC-compatible hinges and rollers on the truck, so most replacements are done in a single visit. The way owners usually find us: the gate starts dragging at the bottom, makes a grinding sound when it swings, or the leaf sags enough that the latch no longer lines up. Those are hinge and roller failures, not operator failures, and replacing them before they chew up the track or twist the gate frame saves real money.

Call (516) 559-4870

Lonnie Burke has been diagnosing this exact failure across Hempstead for years now, including a long stretch of properties near Hofstra where the older FAAC swing gates take a beating from constant use. The part itself is simple. Getting the size and load rating right is what separates a fix that holds from one that fails again in eighteen months.

Which FAAC Models This Applies To

Most FAAC swing gate operators in Hempstead use one of two hinge configurations. The FAAC 400 series, the 412, and the 415 take a barrel hinge with a sealed roller bearing at the pivot point. The heavier 750 and 760 series use a larger bolster hinge, and those rollers are rated for more weight because the gate leaves run longer and heavier. If you have a FAAC slide gate, the rollers are a different animal entirely: those sit under the gate leaf and ride a track, and we cover those separately.

The compatibility gotcha: FAAC has changed hinge mounting patterns between production runs. A hinge from a 412 manufactured in 2011 will not always match the bolt pattern on a gate hung in 2019, even if the model number is identical. We bring both patterns on the truck and measure the old part against the new one before anything gets bolted on. For OEM versus aftermarket, we stock genuine FAAC hinges and rollers because the hinge is what carries the entire weight of the gate leaf. A cheap aftermarket hinge with a softer bearing fails early, and then the gate drops, and then the operator strains against a misaligned leaf, and a $40 part becomes an $800 operator repair. That is a trade we will not make on your behalf. Carver Gate Repair Hempstead is an independent service provider, not affiliated with FAAC, but we match parts to the original specification because that is what the gate was engineered for.

Signs Your FAAC Hinge & Roller Replacement Is Failing

• The gate leaf sags at the latch end. The hinges wear unevenly, the top hinge opens up first, and the latch drops half an inch below the strike. That half inch is the distance between “locks at night” and “swings open in a stiff wind.”
• You hear a grinding or squealing when the gate moves. The roller bearing has gone dry or flat-spotted. Squealing is the bearing crying for grease it can no longer hold; grinding means the bearing surface is already damaged.
• The gate shudders or binds partway through its travel. A worn roller no longer carries the leaf smoothly, so the operator has to push through a flat spot on every cycle. That extra load shortens the operator’s life.
• The gate scrapes the driveway or leaves a wear mark in the concrete. The roller’s outer surface has worn down enough that the leaf is riding lower than it should. In Hempstead, winter salt and sand accelerate this wear considerably.
• The operator opens or closes the gate in jerks instead of a smooth arc. When the hinge or roller binds, the FAAC operator’s torque sensor kicks in and out. The gate moves a few inches, pauses, moves again. The operator is trying to tell you something.

Replacement Cost & What’s Included

Here is what FAAC hinge and roller replacement costs in Hempstead:

• Single gate leaf, standard hinge set, two hinges: $220 to $320 installed
• Single gate leaf, hinge set plus roller replacement: $280 to $400 installed
• Double gate (two leaves, full hinge and roller replacement): $380 to $480 installed
• Heavy FAAC 750/760 series hinges: add $60 to $100 per hinge due to the larger part and longer install time

Those numbers include the parts, the labor, the adjustment of the gate so it swings level with the operator’s travel limits, and the re-greasing of all pivot points. We hand you a written price before any work starts, and that price is what you pay. If the gate leaf is badly misaligned from running on bad hinges, we may recommend a track or operator adjustment after the hinges are replaced; that is quoted separately and agreed to before we do it. Every repair carries our written one-year guarantee. If the hinge or roller fails inside that window, we come back free.

DIY or Call Us?

You can check two things without any risk. First, look at the gap between the gate leaf and the post at the hinge side: if it is wider at the top than the bottom, the hinges have sagged. Second, lift the end of the leaf gently; if it moves up an inch or more, the rollers are shot. What you should not do is unbolt the gate yourself. A full-size FAAC gate leaf weighs hundreds of pounds, and a hinge bolt under tension can release fast. If the gate drops off the last hinge while you are under it, that is a hospital trip. And there is a real safety issue beyond the weight: an improperly supported gate can swing free and hit a person or a vehicle. This is a job for a crew that has done it hundreds of times with the right stands and the right sequence. If the gate’s not right, we’re not done. Call (516) 559-4870 and we will quote it over the phone in about fifteen minutes, then schedule the visit.

FAQs